------------------------------------

TrainRocket.com helps you document every process and policy in your business so you can onboard, train, and scale faster.

Get started with TrainRocket.com for FREE!

------------------------------------

A drill and tap chart details the right size of drill bit to use to create the appropriate sized opening that would complement tap dimensions. A tap drill chart is important in pairing up female and male threads so they connect securely. When you buy dies and taps, it often turns out that you also get the corresponding dies and taps. However, for sizes of the drills only, the particular drill chart is essential.

Tap is required to make female thread. The die is manufactured with a split on its side, and it can be used to fine-tune screws and to create threads on different materials.

Free Tap Drill Chart 01
Free Tap Drill Chart 02
Free Tap Drill Chart 03
Free Tap Drill Chart 04
Free Tap Drill Chart 05
Free Tap Drill Chart 06

How to Convert Drill Bit Sizes

The first thing you do is find the tap drill chart and look for the accompanying drill bit size. Tap drill charts will give you the right tap for drilling in both measurements of millimeters and inches. You need taps for manufacturing of parts, which are tools that make holes with female screw threads when building and fastening. There are tons of different ways you can make this hole, but using a tap to thread the hole is the most common one.

All standard size taps usually come with at least one drill bit size that matches it. These are a bit bigger than the skinniest area of the male screw, but still smaller than the thickest area of that screw. When you want to find the right drill-and-tap size, you also need to know what type of screws you will be using. This is important in determining the right drill bit size. This is because a tap is able to make a varying depth of water depending entirely on how big a hole is.

Drill Size Chart Examples

Free Tap Drill Chart 07
Free Tap Drill Chart 08
Free Tap Drill Chart 09
Free Tap Drill Chart 10
Free Tap Drill Chart 11
Free Tap Drill Chart 12
Free Tap Drill Chart 13
Free Tap Drill Chart 14

How Can Use the Drill Chart

Manufacturers use the chart to determine what drills and taps they need to produce female screw guides. The fact that they are able to do so is what allows workers and homeowners to complete predrilled items. Drill and tap charts use drill sizes to figure out what size hole, or tap, is right for the job. Manufacturers make a hole of the right length, put a tap in it, and start making the threads. The taps are designed to carve out guides of the right size. It provides security that the screws are nice and snug. Wood and metal components work quite well with drill charts.

The Imperial Charts allow users to compare diameters in inches instead of in millimeters. When you’re faced with guides that cover over an inch sized drill bits, it fulfills the same purpose. You need to know what depth you need so that you only use one chart for making guides.

To re-drill the existing hole, first you will need to create a fresh thread by adding thread. Use the tap and drill chart to find the correct size for your hole and start drilling. Next, put the square end on top of the holder and tighten it. Once the tap is in place, you should position the tap so that it is perpendicular to the hole. You then turn the tap inside the hole. It cuts the thread in the wall of hole. After two full turns, turn your faucet back around halfway or three-fourths of a turn. This helps loosen the chip.

It is important to remember that if you are working with dies, or are thinking of using them, you should know that they are used the same way. The only differences between the two are that they are applied on a round rod and not a drilled hole. The size of the die must equal the size of the rod.

Drill Bit Sizes

Free Tap Drill Chart 15
Free Tap Drill Chart 16
Free Tap Drill Chart 17
Free Tap Drill Chart 18
Free Tap Drill Chart 19
Free Tap Drill Chart 20

How to Read a Tap Drill Chart

The tap and die chart shows different drill sizes and diameters. All you have to do is match the size of the drill bit to the material type and the thread count. Internal threads are cut by taps. They are available in different types, including- Machine screw, taper, plug, and bottom.

Taper taps are used to cut threads in a hole. Plug taps are used to cut threads on the end of a partially drilled hole. Machine screw taps are meant for small diameter holes, and is the smallest you will find. Bottoming taps have a special design so they can go through entirely to the bottom of a hole.

------------------------------------

TrainRocket.com helps you document every process and policy in your business so you can onboard, train, and scale faster.

Get started with TrainRocket.com for FREE!

------------------------------------